您的位置:网站首页 > 机械制图 > 机械知识

模具厂常用之标准零配件英汉对照(上)

时间:2011-03-15 12:22:13 来源:未知
         

  air vent vale通气阀anchor pin锚梢angular pin角梢baffle调节阻板

  angular pin倾斜梢baffle plate折流档板ball button球塞套ball plunger定位球塞

  ball slider球塞滑块binder plate压板blank holder防皱压板blanking die落料冲头

  bolster上下模板bottom board浇注底板bolster垫板bottom plate下固定板

  bracket托架bumper block缓冲块buster堵口casting ladle浇注包

  casting lug铸耳cavity模穴(模仁) cavity retainer plate模穴托板center pin中心梢

  clamping block锁定块coil spring螺旋弹簧cold punched nut冷冲螺母cooling spiral螺旋冷却栓

  core心型core pin心型梢cotter开口梢cross十字接头

  cushion pin缓冲梢diaphragm gate盘形浇口die approach模头料道die bed型底

  die block块形模体die body铸模座die bush合模衬套die button冲模母模

  die clamper夹模器die fastener模具固定用零件die holder母模固定板die lip模唇

  die plate冲模板die set冲压模座direct gate直接浇口dog chuck爪牙夹头

  dowel定位梢dowel hole导套孔dowel pin合模梢dozzle辅助浇口

  dowel pin定位梢draft拔模锥度draw bead张力调整杆drive bearing传动轴承

  ejection pad顶出衬垫ejector脱模器ejector guide pin顶出导梢ejector leader busher顶出导梢衬套

  ejector pad顶出垫ejector pin顶出梢ejector plate顶出板ejector rod顶出杆

  ejector sleeve顶出衬套ejector valve顶出阀eye bolt环首螺栓filling core椿入蕊

  film gate薄膜形浇口finger pin指形梢finish machined plate角形模板finish machined round plate圆形模板

  fixed bolster plate固定侧模板flanged pin带凸缘flash gate毛边形浇口flask上箱

  floating punch浮动冲头gate浇口gate land浇口面gib凹形拉紧

  goose neck鹅颈管guide bushing引导衬套guide pin导梢guide post引导柱

  guide plate导板guide rail导轨head punch顶冲头headless punch直柄冲头

  heavily tapered solid整体模蕊盒hose nippler管接头impact damper缓冲器injection ram压射柱塞

  inlay busher嵌入衬套inner plunger内柱塞inner punch内冲头insert嵌件

  insert pin嵌件梢king pin转向梢king pin bush主梢衬套knockout bar脱模杵

  land合模平坦面land area合模面leader busher导梢衬套lifting pin起模顶

  lining内衬locating center punch定位中心冲头locating pilot pin定位导梢locating ring定位环

  lock block压块locking block定位块locking plate定位板loose bush活动衬套

  making die打印冲子manifold block歧管档块master plate靠模样板match plate分型板

  mold base塑胶模座mold clamp铸模紧固夹mold platen模用板moving bolster换模保持装置

  moving bolster plate可动侧模板one piece casting整体铸件parallel block平行垫块paring line分模线

  parting lock set合模定位器pass guide穴型导板peened head punch镶入式冲头pilot pin导

  pin gate针尖浇口plate衬板pre extrusion punch顶挤冲头punch冲头

  puncher推杆pusher pin衬套梢rack机架rapping rod起模杆

  re-entrant mold凹入模retainer pin嵌件梢retainer plate托料板return pin回位梢

  riding stripper浮动脱模器ring gate环型浇口roller滚筒runner流道#p#分页标题#e#

  runner ejector set流道顶出器runner lock pin流道拉梢screw plug头塞set screw固定螺丝

  shedder脱模装置shim分隔片shoe模座之上下模板shoot流道